Might wanna switch that F to a C.
Might wanna switch that F to a C.
How about some of those “protections” you are giving to tech given to the people?
Silly me we don’t like the people anymore.
I brows Lemmy by all and then I filter out the communities I don’t want to see. This lets me see the new communities that pop up and decided if I want to sub to them. I have around 300 blocked.
PETG is picky about layer heights and speed.
Thick and slow for PETG. I usually double my layer height vs what I would print in PLA. With my .6 nozzle I print with .3 layer and cut my speed down to 50% for the first layer. Since you said it happens mid print you might be printing too fast for the first few layers and it is getting too high because the layer is not cooling enough and it starts curling. You can also try reducing flow if your nozzle is worn and it’s allowing more plastic than the sclicer expects which will cause too high layers and scraping.
Oh and it sounds like it’s too hot too. 80° bed in a enclosure could cause the chamber to get too hot and not allow the layers to cool fast enough and so you will see curling while printing. Lower the bed to 40-50 and monitor chamber temps. Maybe open the doors a crack. You only need an enclosure for PETG if the room is drafty.
That’s 2 heading cards, one is set as the title and the other as subtitle. The title has the navigation option turned on to navigate to that room. And the subtitle is just filled with entities. I then use a entities card set with just the divider. It’s a messy way to do it but it was the best I could figure.
Just to give an idea what I use it for based on my Home Dashboard
Office is under remodel which is why the sensors are offline.
Been using it for awhile now. Do we have a way to use our phones as the play yet? I want to be able to listen on my phone with headphones or even in my car with Android Auto. I would love to be able to delete my Spotify app. I still use the service because the radio feature is still much better than MA. But once I can do everything that Spotify can be I can cancel my Spotify account.
I love how most of the decent world is watching what Trump does and immediately does the opposite.
Trump “make it illegal”
Poland “make that easier”
Doritos™ presents, I don’t normally read long posts but I was hooked from the start.
Well VW is still around. Maybe Teslas will be classic cars in 80 years.
/s: They will all self immolate.
American cheese used to cost more than eggs. Now cheese is 10x cheaper than eggs. New throwables just dropped.
I don’t print that often but I do have a calendar event to tell me to print something monthly. This could be a nice side project for someone to write a program that sends a print to your printer on a schedule to keep the heads clear. Wastes paper but at least the heads won’t dry out.
If everyone has it then it would be the purge everyday as everyone will be keeping in RAM the fact they are in a time loop, and dieing does not matter.
Oops the stream hallucinated and mutated into a horror show with women with nipples that are mouths and dicks with eyeballs.
Ok I checked it out, why are there so many people with boobs and with 3 foot cocks? Talk about unrealistic body expectations.
I buy hard drives, it is the best way to own a physical copy of media. Arr
Arr, those be the high seas now
Won’t work, as you thrust your ass will pull away. Only way I could think of is having the portals on platforms that would move with you.
That is a bed leveling issue. It’s too far away where there are gaps and too close where there is rippling. Run a bed leveling procedure and if the model allows for manual leveling you should go through that and then do another mesh leveling.
Also clean your build plate with soap and water and avoid touching it with bare hands.
Sounds like a thermal runaway where a temperature changed too quickly and the code interpreted that as a fire or risk of fire and shut down. A lot of times that can be helped with a silicone sock and a PID tuning. Another thing is the ceramic heater core is going bad and it can’t keep a stable temp above a point. Heater cores are cheap and easy to change. The heater core is considered a consumable part and usually comes in multiple packs.